search  current discussion  categories  kilns & firing - burners 

question about burners for olympic 2327 fas kiln

updated wed 16 nov 11

 

John Post on sun 13 nov 11


I just purchased a used olympic 2327 updraft gas kiln on e-bay. The
body of the kiln is in great shape. The burner system plugs into a
kiln sitter on the kiln. I posted some pictures of the burner system
on my photobucket page.

Is it possible to tell by looking at these burners and connections if
they are set up for natural gas or propane? Or if I would be better
off putting different burners on this kiln?

http://i1210.photobucket.com/albums/cc419/ucsartteacher/001-1.jpg

http://i1210.photobucket.com/albums/cc419/ucsartteacher/003-1.jpg

http://i1210.photobucket.com/albums/cc419/ucsartteacher/005-1.jpg

http://i1210.photobucket.com/albums/cc419/ucsartteacher/004-1.jpg

http://i1210.photobucket.com/albums/cc419/ucsartteacher/002.jpg

Thanks,

John Post
Sterling Heights, Michigan

http://www.johnpost.us

Follow me on Twitter
https://twitter.com/UCSArtTeacher

Eric Ciup on mon 14 nov 11


A. Check the Basso valve (the box with the red button),to see what
pressure its rated at, if it is 1/2 psi you can fire natural gas or low
pressure propane. 5 psi or higher and you can fire high pressure propane.

B. Check the size of the orifices in the burners, if they are 1/4" or
larger then its definitely a low pressure system.

http://www.joppaglass.com/burner/highp_chart.html
http://www.joppaglass.com/burner/lowp_chrt.html


C. Change the last bits of pipe. Galvanized steel is not allowed on
burners , you need black iron pipe.

On 11/13/2011 10:36 PM, John Post wrote:
> I just purchased a used olympic 2327 updraft gas kiln on e-bay. The
> body of the kiln is in great shape. The burner system plugs into a
> kiln sitter on the kiln. I posted some pictures of the burner system
> on my photobucket page.
>

Vince Pitelka on mon 14 nov 11


John Post wrote:
Sent: Sunday, November 13, 2011 9:36 PM
I just purchased a used olympic 2327 updraft gas kiln on e-bay. The body o=
f
the kiln is in great shape. The burner system plugs into a kiln sitter on
the kiln. I posted some pictures of the burner system on my photobucket
page. Is it possible to tell by looking at these burners and connections i=
f
they are set up for natural gas or propane? Or if I would be better off
putting different burners on this kiln?

Hi John -
There is no way to tell from those photographs. What you need to do is tak=
e
one burner apart and check the size of the orifice with a number drill set,
and then call Olympic. Once you know the orifice size they should be able t=
o
tell you whether it is set up for propane or natural gas. I know that
people have had trouble with some of the stock burners that come on Olympic
gas toploaders, but you won't know until you try these. If you do have
trouble with them, then replacing them with GACO MR-750 venturis would be a
good move, but it will cost you between $250 and $300 for five of them.
- Vince

Vince Pitelka
Appalachian Center for Craft
Tennessee Tech University
vpitelka@dtccom.net
http://iweb.tntech.edu/wpitelka/

Steve Mills on tue 15 nov 11


John,=3D20
This is identical to an Olympic I had many years ago, especially the Burner=
s=3D
.=3D20
The instruction was that these were set up for low pressure gas, either Na=
t=3D
ural or Propane. Operating at 50 millibars or less. Because they are a comp=
r=3D
omise, they are not "the best", but they worked for me, and I got some damn=
g=3D
ood firings out of that kiln on Propane, using half shelves not full round =
o=3D
nes to assist flow.=3D20
It is essential however that you set a baffle plate at the top of the setti=
n=3D
g 1.5" below the flue hole (I used a 10" X 10" shelf). I also changed the s=
h=3D
ape of that from a round hole to a slot with two bits of kiln shelf and use=
d=3D
them as dampers.=3D20
Worked really well for me.=3D20

Steve M


Steve Mills
Bath
UK
www.mudslinger.me.uk
Sent from my Ipod touch

On 14 Nov 2011, at 03:36, John Post wrote:

> I just purchased a used olympic 2327 updraft gas kiln on e-bay. The
> body of the kiln is in great shape. The burner system plugs into a
> kiln sitter on the kiln. I posted some pictures of the burner system
> on my photobucket page.
>=3D20
> Is it possible to tell by looking at these burners and connections if
> they are set up for natural gas or propane? Or if I would be better
> off putting different burners on this kiln?
>=3D20
> http://i1210.photobucket.com/albums/cc419/ucsartteacher/001-1.jpg
>=3D20
> http://i1210.photobucket.com/albums/cc419/ucsartteacher/003-1.jpg
>=3D20
> http://i1210.photobucket.com/albums/cc419/ucsartteacher/005-1.jpg
>=3D20
> http://i1210.photobucket.com/albums/cc419/ucsartteacher/004-1.jpg
>=3D20
> http://i1210.photobucket.com/albums/cc419/ucsartteacher/002.jpg
>=3D20
> Thanks,
>=3D20
> John Post
> Sterling Heights, Michigan
>=3D20
> http://www.johnpost.us
>=3D20
> Follow me on Twitter
> https://twitter.com/UCSArtTeacher

William & Susan Schran User on tue 15 nov 11


On 11/13/11 10:36 PM, "John Post" wrote:

> I just purchased a used olympic 2327 updraft gas kiln on e-bay. The
> body of the kiln is in great shape. The burner system plugs into a
> kiln sitter on the kiln. I posted some pictures of the burner system
> on my photobucket page.
>
> Is it possible to tell by looking at these burners and connections if
> they are set up for natural gas or propane? Or if I would be better
> off putting different burners on this kiln?

John,
There is no way to tell if burners are to be used for propane or natural
gas.
It is the orifice (fitting with tiny hole) down inside the burner that
determines that. You will need to take apart the burners - looks like you'l=
l
need a good bit of WD40 - to get to the burner's guts. The orifice is a
small brass fitting down near bottom of the burner tube.

You might also see if you can read the model/serial numbers and call Olympi=
c
to see if there is a designation that would tell you which fuel it uses.

Bill

--
William "Bill" Schran
wschran@cox.net
wschran@nvcc.edu
http://www.creativecreekartisans.com

Rob Addonizio on tue 15 nov 11


John,
Although this is probably less info than you need, I can tell you that th=
=3D
e only=3D20
way to tell is to check the size of your orifice. I have an old copy of O=
=3D
lsen's=3D20
Kiln Book and it has the info. I can send it to you if need be for the sp=
=3D
ecific=3D20
number.

OR... if you know which fuel you are going to use you can always change=3D2=
0=3D

them out with new ones depending on what you need.


BTW, I thought you were not going the Olympic Torchbearer route....?

I am sure you have a great plan anyway!

Take care you you awesome art teacher you...
Rob